Teadlased 3D prinditud inimese munandirakud
Mar 18, 2022
Jäta sõnum
Kanada Briti Columbia (UBC) teadlased kasutavad 3D-tehnoloogiat inimese munandirakkude printimiseks ja avastavad, et neil on varajased tunnused spermatosoidide tootmiseks, mis on esimene kord maailmas. UBC uroloogia assistendi abiprofessori dr Ryan Flannigani uurimisrühmal on üks-päev, mis pakub lahendust patsientidele, kes ei saa praegu ravida.

"15 percent of the couple suffer from infertility, at least half of them is caused by male factors." Flannigan said its laboratory established a Vancouver's prostate center in Vancouver General Hospital. We are printing testicular cells into a special structure that imitates the human anatomy with 3D printing technology, which we believe this is the best way to stimulate sperm generation. "Flannigan said, if success, this will open the new birth treatment door for those who have no other choice.
Inimese munandites toodab sperma väike toru, mida nimetatakse peeneks toruks. Kõige raskema meeste viljatuse -mitte-obstruktiivse mitte-spermahaiguse (NOA) korral leitakse spermatosoidid ejakulatsioonis nende väikeste torustruktuuride poolt toodetava sperma vähenemise tõttu. Kuigi mõnel juhul võib arst aidata NOA patsientidel leida operatsiooni teel üliharuldasi spermatosoide, ütles Flannigan siiski vaid poole edukuse määrast.
"Unfortunately, for the other half of patients, they have no choices, because we can't find sperm for them." Flannigan said, these is the patient who wants to help. In recent studies, researchers conducted biopsy for testis of NOA patients and collected stem cells. These cells were then cultured, and 3D was printed into a hollow tubular structure on the petri dish, similar to the fine elipes capable of producing sperm.
After 12 days, the research team found that these cells did not only survive, but also growing several special cells participating in sperm production, and there was significant improvements in the maintenance of stem cells - this is the early signs of sperm production capacity. The results of this study were recently published in "Plastic and Infertility Science".
"These cells survive and start differentiation, which is a huge milestone. Although there is still a long way to go, this makes our team full of hope." Flannigan said.
The team is currently committed to the "training" cells producing sperm. In order to do this, they exposed cells in different nutrients and growth factors, and fine-tuned their structural arrangements to promote interaction between cells. If these cells can produce sperm, these sperm may pass through in vitro fertilization Make the egg fertilization and provide a new birth treatment option for the couple.
Uurimisprojekt paljastab ka geneetilised ja molekulaarsed mehhanismid, mis viivad NOA tekkeni. Flannigani meeskond on kasutanud mitmesuguseid üksikute{0}}raku järjestamise tehnikaid, et mõista iga raku geeniekspressiooni ja omadusi ning seejärel arvutada mudel välja, et paremini mõista haiguse algpõhjust ja määrata uus raviplaan. See töö vajab ka tihedat koostööd, kaasates UBC teadlasi arvutiteaduse, matemaatika ja inseneritöösse ning muusse rahvusvahelisse koostöösse.
"We are increasingly learned that infertility may have many different reasons, and every case varies from person to person." Flannigan said, "Considering this, we are taking a personalization, precise Medical Methods - Extracting the cells from the patient, trying to understand its unique abnormal conditions, and then supported by 3D printing to overcome these original defects. "
